Moulded Ogee Guttering

Moulded Ogee Guttering – We design and manufacture the finest quality Moulded Ogee Guttering, available with over 200 polyester powder coat colours.

Aluminium in Construction

Moulded Ogee Guttering

The Guttermaster Moulded Ogee Guttering is taken from a traditional cast iron pattern to provide a strong, long-lasting, yet lightweight and economical gutter to give a decorative eaves detail on a wide range of applications.

It can be used as a direct replacement for cast iron on refurbishment, or on new build.

Thick gauge extrusion, using a high strength alloy 6063 T6, allows us to produce a much straighter gutter than other methods of manufacture (1.5mm/metre for extrusion compared with 3.5mm/metre for casting).

Moulded Ogee Guttering

Moulded Ogee Guttering

Benefits & Special Features

System Information

We aim to make all system information and options available.  If you have a requirement which we have not covered then please don’t hesitate to contact our technical department to discuss how we can tailor a solution for your next project.  

Benefits
  • To prevent leakage, the lip detail at the top of the gutter section enables the joint to lock into place
  • The vertical rear face of the gutter reduces unsightly gaps which can be particularly noticeable on polyester coated systems whilst allowing the gutter to be fixed to a fascia without brackets if required
  • Exceeds British standard thickness requirements
  • To prevent wind uplift the Guttermaster system incorporates wind restraint lips which lock the gutter into position
  • Extra large gutters available up to 400mm wide, 300mm deep
Testing

All our tests are independently carried out by leading test institutes. Throughout the programme our products are first tested to realistic parameters and current industry standards.  Testing often proceeds to the point of destruction in order to see how high we’ve set the bar.  The results, whilst pleasing to our design team, also instill confidence in the minds of our customers and end users industry wide.

Download our snow loading test report

Finishes

The Guttermaster aluminium range is available Polyester powder coated to outside surfaces in strict accordance with BS6496. Colours available are standard ‘RAL’, ‘BS4800’ or ‘Syntha Pulvin’ reference.

We also offer a wide range of alternative finishes including heritage textured finish, metallic, anodised coating, aswell as made to order special colours and finishes.

View Guttermaster colour chart

PDF Downloads

Download free Adobe PDF Reader

The following links will open the Product Information Sheets in a separate window, they can then be saved to your computer.

Moulded No.46 Aluminium Guttering.pdf

AutoCAD Downloads

Download free Autodesk DWG TrueView

To download this profile to your computer, click on the link below the image. Select “Open” and choose a path to save the file.

MG/5×4.dwg

MG/6×4.dwg

MG/8×6.dwg

 

BIM Downloads (Revit)

Download free Autodesk Viewer

To download this BIM file to your computer, click on the link(s) below. BIM files are stored in Revit formats and are available in Lite and Detailed layouts. User Guides are PDF.

Download Moulded No.46 System Revit Files (includes user guide)

Moulded Ogee Guttering Capacities & Compatible Rainwater Pipe

RAINWATER PIPE FOR MOULDED GUTTER

Fixing Types

Direct Fixing – No Brackets

Moulded Ogee Guttering

Position the outlets to line up with drain location. Fix the outlets to the fascia board using the slots provided.  Similarly, fix angles and stop ends.  Set a line between the outlets and angles or stop ends and fix gutter lengths at maximum 500mm centres, again using the slots provided.  Gutters should be secured to fascia board with No. 10 x 25mm zinc plated or stainless steel roundhead twin threaded screws.

Fixing with Fascia Brackets

Moulded Ogee Guttering fascia brackets

Position the outlets to line up with drain location. Fix fascia brackets within 300mm either side of the outlets. Fix additional brackets within 150mm of angles and stopends. Set a line between these brackets, all remaining brackets should then be fixed at maximum 1,000mm centres. Brackets should be secured to fascia board with No. 10 x 30mm zinc plated or stainless steel countersunk twin threaded screws. The gutter is a ‘Snap’ fit under the wind restraints.

Fixing to side & top Rafters

Moulded Ogee Guttering rafter brackets

Position outlets as Option B.  Bracket locations will be dictated by the rafter positions.  For this reason it will be necessary to reduce the fixing centres to 600mm maximum.  In practice this will usually mean that every rafter will have a bracket..

Rafter brackets should be secured using No.12 x 40mm. zinc plated or stainless steel countersunk twin threaded screws.

Rise & Fall Mortar Brackets

Moulded Ogee Guttering rise & fall brackets

Position outlets as Option B.  Bracket centres to 1000mm maximum, with a bracket at either side of all outlets and corners.  Incorporates additional wind restraint breacket

Fix directly to brickwork by drilling out an opening in the mortar then hammering the spike into the opening.  Best suited to uneaven walls or where fixings to the fascia cannot be achieved.

 

 

Moulded Ogee Guttering Standard Components

Standard Gutter Length

Use maximum lengths to minimise joints.

Moulded Ogee Guttering lengths
STANDARD GUTTER LENGTHS
Fascia brackets – with wind restraint

Other types of brackets available – please enquire

Moulded Ogee Guttering brackets
MOULDED FASCIA BRACKETS
RUNNING OUTLETS

INCREASE ‘L1’ ON DEEP FASCIA BOARDS

Moulded Ogee Guttering outlets
MOULDED RUNNING OUTLETS
ANGLES

STANDARD 90° AND 135° – NON-STANDARD AVAILABLE

Moulded Ogee Guttering corners
MOULDED GUTTER ANGLE
Rafter Brackets – with wind restRaint

TOP FIXING (MRT)

Moulded Ogee Guttering rafter brackets
MOULDED GUTTER WIND RESTRAINT
Rafter Brackets – with wind restRaint

SIDE FIXING (MRS)

Moulded Ogee Guttering side fix rafter brackets
MOULDED RAFTER BRACKETS SIDE FIX
STOP ENDS

HANDED COMPONENT

Moulded Ogee Guttering stop ends
MOULDED GUTTER STOP ENDS
UNION JOINTS

APPLY LOW MODULUS NEUTRAL CURE SILICONE TO BS5889 (TYPE A)

Moulded Ogee Guttering union joint
MOULDED GUTTER UNION JOINT

Purpose Made Components

As a manufacturer of Moulded Ogee Guttering for over 25 years, we have developed a wide range of bespoke and optional components which can be incorporated into your chosen gutter system.  These components include but are not limited to:

Scroll Brackets

Moulded Ogee Guttering scroll brackets

Lightning Clips

Moulded Ogee Guttering lightning clips

Raking Angle

Moulded Ogee Guttering raking angle

Radius Gutters

Moulded Ogee Guttering curved

Back Outlet

Moulded Ogee Guttering back outlet

Moulded Ogee Guttering – Documents

Snow Load Test Report

Associated Products

Cleaning & Maintenance

Moulded No.46 System

Jointing Instructions

Jointing Section Detail

Moulded Ogee Guttering – Eaves Combination Examples

Glazed Canopy Gutter

Gutter Eaves Detail

Monopitch Roof

Reduced Fascia

Get a Quote For Your Project